V1291 Complete Compressor Installation Kit for Vehicles without Air Brakes

Part Number: V1291

$ 565.00

The V1291 is a complete kit that includes a compressor, air tank, solenoid valve, and all of the fittings needed to install your Grover®️ air horn onto a vehicle without air brakes.

This kit is compatible with all Grover single Stuttertone®️, Truktone®️, and Organtone®️ air horns.

For dual horns under 30 inches, use the V1291DM installation kit.

For dual horns 30 inches and above, use the V1291DL installation kit.

 

GROVER V1291 Complete Installation Kit Components

  1. Viair compressor
  2. Viair Air tank
  3. Grover 1136 valve
  4. Horn Button with screws
  5. Pressure switch
  6. ¼ pipe size Tee
  7. Air safety valve for air tank
  8. Drain cock
  9. 2 x ⅛ NPT male compression fittings (one for 1136 valve inlet, one for air horn)
  10. 1 x ⅛ NPT female compression fitting (for 1136 valve outlet)
  11. 1 x ¼ NPT male compression fitting (for air tank, to connect to 1136)
  12. 4 x tube supports
  13. 12 feet Wire
  14. 12 feet ¼” OD air Tubing
  15. Thread sealant tape
  16. Instructions
-
+
SKU: V1291

DISCLAIMER AND WARNING

These instructions are provided as a general guide for installation. Vehicle configurations, wiring layouts, and mounting locations vary. The installer is responsible for verifying that all electrical and pneumatic connections are correct and safe for the specific vehicle.

Grover Products assumes no responsibility for damage, injury, or vehicle malfunction resulting from installation errors, incorrect wiring, improper component use, or reliance on these instructions without proper verification.

Sound levels of Grover®️air horns may exceed 120 dB and can cause permanent hearing loss. Minimize exposure and wear hearing protection. Do not sound indoors or in enclosed areas. Do not exceed 125 PSI.

INSTALLATION GUIDELINES

All installation and testing must be performed by qualified personnel familiar with automotive electrical and compressed air systems.

Disconnect the vehicle battery before beginning installation. Use thread sealant on all NPT fittings. Use tube supports on all compression fittings. Tighten all fittings securely to maintain an airtight system.

PNEUMATIC CONNECTIONS

Step 1. Compressor to Tank

Use the stainless braided leader hose supplied in the Viair compressor box. Thread the leader hose directly into any ¼ NPT port on the air tank. Do not remove the integrated check valve.

Step 2. Pressure Switch and air safety valve

Attach the ¼ pipe size Tee to any unused ¼ NPT port on the air tank. On one branch of the Tee, install the air safety valve to prevent over-pressurization. On the other branch install the pressure switch. The pressure switch must be wired to shut off the compressor at the rated cut-out pressure.

Step 3. Drain cock

Install the drain cock in the lowest ¼ NPT port on the air tank.

Step 4. Tank to 1136 Valve

On the final tank port, install a ¼ NPT male compression fitting with tube support. Run tubing from the tank to the “INLET” port on the 1136 valve using a ⅛ NPT male compression fitting and tube support.

Step 5. 1136 Valve to Horn

Install a ⅛ NPT female compression fitting on the 1136 “OUTLET” port. Connect tubing using tube support. Attach tubing to horn using ⅛ NPT male compression fitting and tube support.

ELECTRICAL CONNECTIONS

The compressor must be wired using a 30A automotive relay rated for continuous duty. Do not power the compressor directly through the pressure switch. Verify vehicle electrical system is 12V DC.

Step 1. Install a 30A fuse within 12 inches of battery positive terminal. Connect fused battery lead to relay terminal 30.

Step 2. Connect relay terminal 87 to compressor positive lead.

Step 3. Ground compressor negative to chassis.

Step 4. Wire the pressure switch between fused ignition or battery source and relay terminal 86.

Step 5. Connect relay terminal 85 to chassis ground.

Step 6. Wire the 1136 valve to the horn button using fused 12V power and ground per standard practice.

Step 7. Secure all wiring away from heat and moving components.

FINAL INSTALLATION

Mount compressor, tank, and horn securely using supplied hardware. Verify clearances from heat and moving components. Reconnect battery. Pressurize system and check for leaks before operation.